The Battle of the Inspection Cameras?

No not really, but we did think it would be fun to lay out 4 inspection cameras from different manufacturers and place their specs, features, and possible unique points side by side to help you, dear consumer, decide which would be best for you.

In no particular order we have:

DeWalt DCT410S1, Draper 13828, RIDGID micro CA-100 and Milwaukee C12IC.

Inspection Camera

The purpose of each of these inspection cameras is simple and the same across the board; to allow you to inspect places not obviously visible with the naked eye.

For example, you're a mechanic who's lost a nut down inside an engine block. Or you're a plumber dealing with an unseen blockage.

The inspection camera you choose, therefore, will need to allow you to flexibly see where your eyes currently can't. If that makes sense. And you also want to be able, in some way, to interact with whatever the camera has inspected. More on that later...

For the most part, each of our 4 inspection cameras will do the job just fine. Each has a flexible arm of around 3 feet or 1 metre in length, with a camera at the end. Each benefits from powerful LED lights affixed around the aperture of the camera, thereby illuminating the area you're inspecting. And each is waterproof, which is essential if you plan on dropping the arm down a toilet or drain.

However, as you'd expect, not all inspection cameras are created equal. So, let's take a bit of a closer look at the spec of each.

First off, how are they powered?

This is an important question, and that's why we're addressing it right at the start. The RIDGID and the Draper are powered via common or garden AA batteries.

Draper 13828 (CAM5) Flexi Inspection CameraThis could be a big plus point for you as it means you don't need to worry about being near a power point to recharge the device.

Alternatively, though, it does mean you're going to need to keep a stock of AA batteries lying around, and we'd recommend stocking up on the high powered variety as they'll be powering the camera, the screen and the LED lights.

With the Draper model, you're going to need to buy 4 AA batteries straight away as, unlike the RIDGID, it doesn't come supplied with any. If you're only likely to be a very occasional user of the inspection camera, the AA battery option may be the best one for you.

The Milwaukee comes supplied with 1.5 AH rechargeable pack, and it's lithium-ion too, which is a bonus.

Yes, you'll need to be prepared to recharge the device, but Milwaukee state a 30 minute charge time coupled with "high run times". Judge this on it's merits; if recharging isn't an issue for you, then perhaps the Milwaukee C12IC scores some points here as you'll never need to remember to bring AA batteries with you!

Dewalt DCT410S1 10The DeWalt is running in a different class in the power stakes, however.

They've brought the DCT401S1 into their fabled 10.8v lithium-ion sub-compact range. So, if you're already a DeWalt user and have already bought into this range of tools, you could buy the naked version and use one of the 10.8v batteries already in your kit. Run time is likely to be fantastic, as you'd expect from a 10.8v li-ion offering from DeWalt.

However, the inclusion of the rechargeable battery does impact on the DCT401S1's price tag.

The matter of what, exactly, these batteries are powering has to come into play next.

Obviously, we're looking at functionality with an inspection camera; we need to be able to inspect, and see - via the camera - inside objects we're inspecting.

Hence, the quality of the images captured by the camera and how these images are displayed to us is important.

How do the 4 cameras in our consideration stack up?

The Milwaukee and Draper offerings are very similar; 2.4" display offering a respectable resolution of 320x240 pixels. With the Draper 13828 coming in at around £50 less than the Milwaukee C12IC, there's not much to separate them.

The RIDGID micro CA-100 and DeWalt's DCT410S1 are very much "the big boys" of the group, boasting 3.5" displays. Size isn't everything, though, it's what's on display that counts.

And the DeWalt just pips RIDGID here, weighing in with an impressive 320x480 pixels against RIDGID's 320x240.

In real terms, both of these inspection cameras are going to give you a lot of "screen real estate". However, the DeWalt is going to show you more detail.

And the DCT410S1's screen is detachable.

This is where DeWalt are innovating. As you can see from this image, the detachable screen will wirelessly receive images transmitted from the camera.

In practical use, this could be a huge boon for you as it allows detailed analysis of the images received from the camera arm while "on the ground". As the photo shows, rather than trying to scrutinise what's on the screen while perched on top of a ladder, a colleague can view the screen while you're using the camera arm.

Image the practical uses this could be put to; underneath car chasis, inside tight ventilation shafts, etc.

That being said, the RIDGID micro CA-100 has a dose of innovation too via the ability to rotate the images on the screen.

Ridgid micro CA-100 (36738) Hand-Held Inspection CameraAgain, this is most easily understood when demonstrated on the job site.

Rather than trying to twist your neck - or arm - in order to get a clear view of what the camera is seeing, you can rotate the image on the screen through 360 degrees.

RIDGID have also paid close attention to customer feedback when developing the micro CA-100, their third generation of SeeSnake micros, as is borne out by the balanced ergonomics of its design.

So, comfort and ease of use seem to be the way forward with RIDGID, while DeWalt have gone all "next generation" with their wireless screen. And Draper and Milwaukee are keeping your wallet in mind with their price point, however that's reflected in the depth of features offered.

Other factors to keep in mind when choosing from one of these inspection cameras is accessory packs.

Ideally you want to be able to deal with the problem that the camera is inspecting, right there and then.

So, for example, that nut that's dropped down inside the engine block; the camera has identified exactly where it is, but how will you get it out? Having a magnetic "hook" to draw the problem out is ideal. As is a hook. Or indeed a mirror for further improving your scope of vision.

Milwaukee C12IC 12V Cordless Digital Inspection CameraDeWalt's DCT410S1 comes with a "kit box" that includes, along with the "fast charger", a hook and a magnet, both of which are fitted to the head of the camera.

RIDGID go one better with the micro CA-100. Obviously, you're not getting the charger as it runs off AA batteries (which are included), but you do get a hook, a magnet and a mirror.

Neither the Draper nor the Milwaukee supply such accessories, but as already noted, they're operating at a keener price point. It's up to you do decide whether you'd need the extra accessories, and if so, you'd be stumping up a  bit more cash for the RIDGID or DeWalt.

Obviously, that extra cash is also buying you a bigger screen and an extra level of screen functionality, as outlined above.

As with any tool, often it's horses for courses, and we all know that existing brand loyalty plays as much of a part in our final choice as anything else; if you've already bought into DeWalt's 10.8v range, then the DCT410S1 is a shoo in.

Milwaukee's lithium-ion rechargeable battery may be a hook for you. As might Draper's price point. Or you may simply have to have the latest on offer from RIDGID, hence the micro CA-100 will be in your basket at the checkout.

Either way, we'd love to know what you think of this "battle of the inspection cameras" and which side you fall down on. Let us know in the comments.


Toolstop on Wed, 13 Mar 2013 09:13:48 +0000 (Likes: 0 / Dislikes: 0

Many thanks for your feedback Robin

robin on Sat, 09 Mar 2013 00:02:56 +0000 (Likes: 2 / Dislikes: 0

I went with the RIDGID. To be fair I didn't try any of the others. I saw the RIDGID at a trade show and loved it. I thought the price for the extra advantage of having it was a bargain. I work in pest control and use it often. Its never let me down yet. I do wish I had got the model which can record images. It would be a lot easier to explain issues to customers with recorded images. It did cost a lot more though.

blog comments powered by Disqus

Select Country:

  • UK - Mainland
  • AustriaAustria
  • BelgiumBelgium
  • BulgariaBulgaria
  • CyprusCyprus
  • Czech RepublicCzech Republic
  • DenmarkDenmark
  • EstoniaEstonia
  • FinlandFinland
  • FranceFrance
  • GermanyGermany
  • GibraltarGibraltar
  • Greece (mainland)Greece (mainland)
  • HungaryHungary
  • IcelandIceland
  • IrelandIreland
  • Isle of ManIsle of Man
  • ItalyItaly
  • LatviaLatvia
  • LithuaniaLithuania
  • LuxembourgLuxembourg
  • MaltaMalta
  • NetherlandsNetherlands
  • Northern IrelandNorthern Ireland
  • NorwayNorway
  • PolandPoland
  • PortugalPortugal
  • RomaniaRomania
  • SlovakiaSlovakia
  • SloveniaSlovenia
  • SpainSpain
  • SwedenSweden
  • SwitzerlandSwitzerland
  • UK - GuernseyUK - Guernsey
  • UK - HighlandsUK - Highlands
  • UK - Isle of ManUK - Isle of Man
  • UK - JerseyUK - Jersey
  • UK - MainlandUK - Mainland
  • UK - N. IrelandUK - N. Ireland
  • UK - OffshoreUK - Offshore
  • United StatesUnited States

Select Currency:

  • BGN
  • CHF
  • CZK
  • DKK
  • EUR
  • HUF
  • NOK
  • PLN
  • RON
  • SEK
  • USD